|
| |
The Lindsay AirGraver™ - Total Modular System
Pistons, bores, handle and controllers, all interchangeable
Lindsay gravers are made from surgical stainless steel.
No aluminum is used in the construction of the tool.
AirGravers and sharpeners have a three week trial return and three year parts and
labor warranty.
Click photos to enlarge
|
Artisan AirGraver™ Handpiece
More information on Artisan AirGraver™, click here
For use with foot pedal controls available further down on this page
Discussion about Lindsay AirGravers on EngravingForum.com
AirGraver forum discussions Page1
Page2
Page3
Page4
More information on Artisan AirGraver™, click here |
$595
 |
|
Classic AirGraver™ Handpiece
More information on Classic AirGraver, click here
For use with foot pedal controls available further down on this page
  
  
Discussions about Lindsay AirGravers on EngravingForum.com
AirGraver forum discussions Page1
Page2
Page3
Page4
More information on Classic AirGraver, click here |
$995
|
|
Tungsten Dead Blow™ Piston
for Classic Artisan Handpiece
The tungsten piston weights approx 3.5 times that of the standard 440C hardened stainless piston. This effetely provides a bigger
hammer (piston) to an AirGraver handpiece. Pistons can be interchanged by a user by removing the handle and swapping pistons. Tungsten Dead
Blow™ Piston $125
|
$125
|
PalmControl™
More
information on PalmControl™, click here
 
Discussions about Lindsay AirGravers on EngravingForum.com
AirGraver forum discussions Page1
Page2
Page3
Page4
More
information on PalmControl™, click here
PalmControls can also be used with the foot controls available further down on this page and switched back
and forth as desired.
Foot Control Classic and Artisan handpieces can be upgraded with a PalmControl handle for $1790. Please
email for details |
PalmControl™ with Classic AirGraver™, full stroke adjustment;
Santoprene handle
$2690
|
|
PalmControl™ with Artisan AirGraver™ (not pictured), non-stroke adjustment;
Santoprene handle |
$2290
|
|
Stabilized burl handle for PalmControl™
More
information on PalmControl™, click here
This burl handle replaces the ivory color Santoprene handle
   
Discussions about Lindsay AirGravers on EngravingForum.com
AirGraver forum discussions Page1
Page2
Page3
Page4 |
$2890
Classic PalmControl/w burl handle
$200
burl handle only
|
|
Stainless and Damascus handles for PalmControl AirGravers
These are additional custom handles that are available for the PalmControl AirGravers.
Click photo to enlarge
EngravingForum thread discussion about these PalmControl Handles
Page 1
Page 2 Page 3 |
303 Stainless
$59
Damascus
$420
|
|
Tungsten Dead Blow Piston
$125
A standard 440C stainless piston comes with an AirGraver. This tungsten piston will weights three times
that of the stainless one and provides heavier impacts throughout the psi ranges as well as the stroke adjustment ranges of the Classic.
The tungsten and stainless piston can be change back and forth as desired by the user. |
$125
|
|
 Lindsay Quick Change extension for Classic
and PalmControl Classic handpieces
These quick change extensions won't wear out. They are made from 440C stainless and hardened to 60 Rockwell. 60
Rockwell is as hard as a high speed steel graver and therefore these QC extensions are made for a life time of service. They are detented for a snap in fit
utilizing the internal O-ring in the nose of the AirGraver handpieces. They extend a graver 5/8". |
2 pack $19.95
5 pack $47.50
10 pack $89.95
|
NitroG20™
AirGraver™
NitroG20™
AirGraver™
For deep engraving as used in
Motorcycle and Heavier Western Engravings
The NitroG20 will work with either a foot control or with a PalmControl handle. It has a larger and
longer internal bore and piston than the Classic or Artisan handpieces. The NitroG20 comes standard with a heavy 20gram Tungsten piston. Price of
the handpiece and tungsten piston is $995. For $75 additional it will have the L slots milled on the back of the body so that a PalmControl handle
will fit and snap on and off of it. CFM air volume requirement to run the tools is 0.9 CFM at 70 to 90PSI. The Supersilent 20-A compressor is too
small. The Supersilent 50-TC is large enough though as it outputs 2.0CFM at 84PSI to 114PSI. Other compressors that can out put at least
.90CFM at 80PSI should work fine with the tool. The tool can also be run with a 80psi CO2 regulator either in a foot control setup or PalmControl setup.
The 80PSI CO2 regulator is listed below.
The NitroG20 is included with one presharpened M42, one M42 graver blank, two HSS graver blanks, handpiece tubing wrenches
and an owners manual. |
Recommended operating PSI for the NitroG20 is 70 to 90 PSI. See below about upgrading your air regulator
gauge and/or CO2 regulator.
Below: Comparison of a 20gram NitroG20 Tungsten piston and a 7 gram Classic Tungsten piston
 |
 NitroG20™
handpiece for a foot control. If you already have a foot control Artisan or Classic this handpiece will run off your current foot control
setup.
The tool holder in this tool will hold 3/32" square and 1/8" round graver shanks as well as other shanks that
will fit within a .133" diameter hole. If you would like to order the handpiece to hold larger 1/8" square and 3/16" round shanks please
write a note saying so in the add to cart "check out" page. |
$995
|
This option provides the NitroG20™ handpiece with L slots milled on back of the body so that if you already own a PalmControl Classic you can use your PalmControl handle on the
NitroG20. The tool is shipped without the black rubber handle shown above so that you can fit your PalmControl directly on the tool when it arrives.
The tool holder in this tool will hold 3/32" square and 1/8" round graver shanks as well as other shanks that
will fit withing a .133" hole. If you'd like the handpiece setup to hold 1/8" square and 3/16" round shanks please write a note in the add to cart "check
out" screen. |
$1,070
|
The tool holder in this tool will hold 3/32" square and 1/8" round graver shanks as well as other shanks that
will fit withing a .133" hole. If you'd like the handpiece setup to hold 1/8" square and 3/16" round shanks please write a note in the add to cart "check
out" screen. |
NitroG20™ PalmControl™ handpiece. The tool can be purchased with
four different handle materials:
1:Ivory color Santoprene
2:Burl wood
3:Stainless steel
4:Damascus
The tool is included with one presharpened M42, one M42 graver blank, two HSS graver blanks, handpiece tubing wrenches
and an owners manual. |
Option #1
$2,690
Option #2
$2,890
Option #3
$2,749
Option #4
$3,110
|
If you already have an AirGraver air regulator you will notice the display on the gauge only goes to 60PSI and so you'll
need this replacement gauge in order to run the NitroG20 at the recommend air pressures of 70 to 90PSI. Simply unscrew your old gauge and screw in
this replacement that displays up to 100PSI. |
$14
|
 |
0-80 PSI CO2 High Pressure Regulator. This is a higher PSI
CO2 Regulator for operating your NitroG20. Also works with Classic and Artisan handpieces.
CO2 80PSI Regulator
$172
20oz paintball cylinder adapter$38 |
CO2 Regulator
$172
20oz Adapter $38
|
Updating a foot control NitroG20™
handpiece to PalmControl™
- $1790
If you would like to update your foot control NitorG20 to PalmControl order this upgrade, and we will contact you when we have a PalmControl
handle made for you. (usually 5 to 10 working day) We will then contact you and you can send your handpiece in for the updated then. The
update will only take couple days this way so you'll be without it for a shorter amount of time.
|
$1,790
|
Handle materials for the PalmControl can be
purchase separately.
Ivory Color Santoprene $25
Burl Wood $200
Stainless Steel $59
Damascus $420
|
|
PalmControl™ and Foot Control Engraving Sets
Foot Control Classic or NitroG20™ engraving set w/ sharpener
Set Includes:
Classic handpiece or NitroG20 (your choice)
Dual regulators
Tungsten Dead blow piston
CarbaltXD graver blanks 5 pack
M42 graver blanks 5 pack
Lindsay Sharpener set with basic templates, Includes: The 4 diamond bench stones (260, 600, 1200, 2000), plus 4 templates: Universal, Detailing, 105, and
Flat & Knife Combo
|
Classic $1,788
NitroG20 $1,788
|
PalmControl™ Classic or NitroG20™ engraving set w/ sharpener
Set Includes:
Classic PalmControl handpiece with Burl handle or a NitroG20 PalmControl h.p.
Tungsten Dead blow piston
Co2 regulator with 20oz and 25g Adapters
Regulator & fittings for attaching PalmControl to an air compressor
CarbaltXD graver blanks 5 pack
M42 graver blanks 5 pack
Lindsay Sharpener set with basic templates, Includes: The 4 diamond bench stones (260, 600, 1200, 2000), plus 4 templates: Universal, Detailing, 105, and
Flat & Knife Combo
|
Classic
$3,693
NitroG20
$3,723
(Difference in price of these is for the
80 PSI CO2 regulator for NitroG20) |
REGULATORS FOR PALMCONTROLS
FOOT CONTROLS
Foot control, idle adjust without regulators
More information about these foot controls (click here)
For operating an AirGraver with a foot control pedal
  |
$179
|
Foot Control, idle adjust and double
regulators
More information about these foot controls (click here)
For operating an AirGraver™ with a foot control pedal
 |
$249
|
CO2 Foot Pedal AirGraver™ Controller
(for Classic or Artisan)
Includes CO2 regulator, foot pedal lines, on/off toggle, idle adjust valve and CO2 adapter for using common 20oz CO2 cylinders that are also used by
paint ball guns. One 20oz bottle will last approximately four to five hours with a foot pedal AirGraver. (Note: A 20oz bottle will last approximately
eight hours when used with a PalmControl Classic AirGraver).
Click photo to enlarge |
$299
|
CO2 Foot Pedal AirGraver™ Controller
(for NitroG20)
Includes high PSI CO2 regulator, foot pedal lines, on/off toggle, idle adjust valve and CO2 adapter for using common 20oz CO2 cylinders that are also
used by paint ball guns. One 20oz bottle will last approximately three to four hours with a foot pedal NitroG20.
Click photo to enlarge |
$329
|
Foot pedal for Rotary dental type hand pieces
Use pneumatic dentist-type drills and rotary hand pieces with an impact AirGraver handpiece by adding this foot control to an AirGraver controller. May be
used with either the AirGraver foot control or PalmControl with an air compressor. |
$69
|
GRAVER SHARPENING
|
 Lindsay
Graver Sharpening System
Click here to view the graver sharpening page
Sharpening Fixture without stones (comes with Universal 116 degree V template)
$89
Sharpening Fixture alone without templates (the metal portion that holds the templates)
$66
Sharpening Fixture with one stone (in your shopping cart type
in a note which grit stone you would like) $128
Sharpener with fixture and all four
diamond bench stones (260, 600, 1200, 2000) (comes with Universal 116 degree V template)
$225
Sharpener set with basic templates, Includes: The 4
diamond stones (260, 600, 1200, 2000), plus 4 templates: Universal, Detailing, 105, Flat & Knife Combo
$294
Click here to view the graver sharpening page
|
$89
$66
$128
$225
$294
|
|
Diamond Bench Stones for Lindsay Sharpener
Bench stone 260 diamond grit (6" x 2" x 1/2") $39
Bench stone 600 diamond grit (6" x 2" x 1/2") $39
Bench stone 1200 diamond grit (6" x 2" x 1/2") $39
Bench stone 2000 diamond grit (6" x 2" x 1/2") $39 |
|
|
Templates sold individually
These and other templates are described on the sharpening page |
70 VlBulino$27
90V$23
"Detailing" 96.3 V$23
105V$23
110V$23
120V$23
Calligraphy" 123 V$23
Phil Coggan Bulino $21
Dario Cortini Bulino$21
Flat & Knife Combo$23
Round Point$23
R. Baptiste inlay $27 |
|
|
Templates for Engraver Carl Bleile's Graver Points
Click here to view the graver sharpening page
 
Tool point descriptions as pictured left to right.
(1) banknote engraving for darker lines (red templates),
(2) scraping tool for removing tool marks, final contouring, also removes excess gold and shapes raised inlays after inlaying (green
template)
(3) background removal tool with special side grinds to get around main area without nicking (blue template).
(4) medium to deep outline, removing background in tight areas, preparing for background removal and gold inlay (red templates).
More information and discussion about Carl Bleile's points and templates on www.EngravingForum.com
Thread 1,
Thread 2,
Thread 3,
Thread 4 Thread 5
Click here to view the graver sharpening page
|
Carl Bleile Template set $68
Sold separately
Deep Line & BankNote (red templates)
$32
Scraper (green template)
$15
Sculpturing & Relief (blue template)
$24
|
|
Ray Cover Templates
Templates sold individually
or in a set
Click photo for enlargement
|
Ray Cover, Background Flat (Use with Ray Cover taper template) $23.00
Ray Cover, BrightCut (Use with Ray Cover taper template) $21.00
Ray Cover, Standard (90 degree) triangle heel (Use with Ray Cover taper template) $21.00
Ray Cover, Taper $16.00
Standard Bulino (Use with Ray Cover taper template) $15.00
Ray Cover, Template Set $89.00
|
|
|
 |
1/2" thick " Cast Iron Lap $59
50,000 Grit Diamond Concentrate
$69
4 ounce concentrate, Makes 32 ounces (1 quart) diamond spray. Mix this concentrate with isopropyl
alcohol.
Concentrate Approximate mix ratio:
7 parts Isopropyl Alcohol
to
1 part Diamond Concentrate
Mixing bottle and push button spray applicator included. |
$59
$69
|
|
 |
1/16" thick 6" Diameter Diamond Sharpening Laps
Will replace laps on power hones originally supplied with 5" diameter laps.
1200 grit diamond lap
$44
600 grit diamond lap
$56
260 grit diamond lap
$65
100 grit diamond lap
$88
|
1200 grit $44
600 grit $56
260 grit $65
100
grit $88
|
Lap Mandrel Adapter
for converting a drill press to a power hone.
  |
Click for information from Carl Bleile on
the engraving forum about the adapter |
$19.50
|
 Graver polishing Apply diamond compound to the back side of a
1/16" thick steel diamond lap (sold above) and use it for polishing graver
facets. When a metal lap is used, some of the diamond will embed itself
into the steel preventing it from wiping off. This is called “charging” a
lap. A copper lap works for this too. Ceramic can also be used, however the diamond will not imbed it self. More information about polishing gravers can be found on the EngravingSchool.com site:
Link 1
Link 2
Note, graver polishing is nessary when you would like bright cutting.
1/2 Micron, 60,000 mesh, 5-gram syringe |
$25
|
|
T. W. Designs
Diamond Power Hone
Variable Speed Graver and Tool Sharpener
Available through the T.W. Designs website
Click Here to go to T. W Designs website |
 |
Available from T. W. Designs
|
LINDSAY GRAVER BLANKS
Hammer & Chisel Engraving
Manual Push Graver Engraving
|
Manual Palm-Push adjustable length graver with supple Santoprene rubber handle (click to enlarge)
 |
This adjustable length graver has 1-1/2" of adjustment. Graver locks securely with no graver wobble with setscrews. Wrench
supplied. $49
(does not include point)
Two unsharpened M42 graver blanks
$20
One Presharpened
CarbaltXD $39 |
$49
$20
$39
|
|
 |
Manual Palm-Push stainless graver, wrench with Lindsay sharpener. Sharpener includes 600 grit
diamond stone, sharpening fixture, 110 degree Uniform-Parallel template, 6"x6" plastic desk plate, and small copper practice plate
$177 (does not include point)
$216 (includes sharpened CarbaltXD point)
Two unsharpened M42 graver blanks
$20 |
$177
$216
$20
|
|
Stainless Chisel that holds 3/32" square gravers for hammer/chisel engraving
click to enlarge |
With the confidence of
Master Engraver Carl Bleile for input of this chisel holder, you are assured hand comfort for hammer & chisel engraving.
Wrench included. $56.50
(does not include point)
Two unsharpened M42 graver blanks
$20
One Presharpened
CarbaltXD $39 |
$56.50
$20
$39
|
|
Chisel holder, Manual push graver and Lindsay
Sharpener set
|
Same Chisel as above plus manual stainless push graver as above, plus sharpener.
Sharpener includes: 600 grit
diamond stone, sharpening fixture, 110 degree Uniform-Parallel template, 6"x6" plastic desk plate, and small copper practice plate
$233.50 (does not include point)
$272.50(includes sharpened
CarbaltXD point)
Two unsharpened M42 graver blanks
$20 |
$233.50
$272.50
$20
|
AIR COMPRESSORS
MICROSCOPES
ENGRAVING VISES
Accessories for Engraving
Pin Vise
 |
Pin Vise: Used to hold small diameter scribe. NOTE: 1/16" diameter friction fit carbide dental burs sharpened
into a point on a diamond lap or stone work great for a small strong scribe or even a Bulino dot tool. Such points are also used for scrimshaw.
$25.37
|
Dividers
 |
Dividers
Used to layout (scribe) borders and divide geometric designs for layout.
$47.37
|
Brass Practice Plate
Wonderful nice nice cutting brass.
Thick (1/4" thick) so there is
no vibration of the plate while engraving
making it ideal for a practice plate.
2"X2" square x 1/4" thick |
Brass Practice plate
$11 each
|
Folding knives with nice cutting 416 stainless handles
 |
1) Model 1-F (D-2 blade) $ 195.00
2) Model 1-f-b (D-2 blade) $ 150.00
3) Model 46 (D-2 blade) $ 90.00
4) Model 3 (440-C blade) $ 50.00
Click photo to enlarge
Order knives direct from maker
P.J. Tomes Knives
594 High Peak Lane
Shipman, VA 22971
434-263-8662
tomesknives@juno.com |
Cindy and Scott at Scottee-Shirts is providing t-shirts, (short and long sleeve) and hoodies with PalmControl and scroll designs. Check out the caveman
master engraver Cindy drew. Select the images and locations on the shirts and order direct from
Scottee-Shirts site. Thanks again Cindy.
Scottee-Shirts site
Image to the right is one of the shirt
PalmControl designs.
Click to enlarge |
 |
 
AirGraver
Show sign
click photos to enlarge |
If you plan to attend a show and would like one of these signs to share with people about the AirGraver, send an email
describing what show or public event you're going to and we can ship you one for no cost. They are 14"x9" and fold up into a small case that is included.
The sign rolls up and fits in the case as well. |
|
|
VIDEOS, BOOKS AND CASTINGS
|
At Browning we have switched to Lindsay tools because we can cut quicker and with better control. I have taught
people to engrave that wanted to learn the art and they absolutely fell in love with the AirGraver. Also, I have let non-engravers play with it and guess what, they starting cutting with no problem.
Rich Hambrook, Browning Arms Company
Additional Feedback |
|
